sillicon graphics octane2を触ってみたよ（OpenBSD起動編）

OpenBSD MIPS

やった、この子はやれば出来る子(￣ー￣)ﾆﾔﾘｯ

Diagnostics failed.
[Press any key to continue.]

System Maintenance Menu

1) Start System
2) Install System Software
3) Run Diagnostics
4) Recover System
5) Enter Command Monitor

Option? 5
Command Monitor.  Type "exit" to return to the menu.
>> printenv
AutoLoad=Yes
console=g
diskless=0
dbaud=9600
volume=80
sgilogo=y
autopower=y
netaddr=192.168.3.2
eaddr=08:00:69:13:67:82
boottune=1
cpufreq=400
SystemPartition=xio(0)pci(15)scsi(0)disk(1)rdisk(0)partition(8)
OSLoadPartition=xio(0)pci(15)scsi(0)disk(1)rdisk(0)partition(0)
OSLoadFilename=/unix
OSLoader=sash
NoAutoLoad=CONSOLE OPEN FAILED.
ConsoleOut=serial(0)
ConsoleIn=serial(0)
>> resetenv
>> setenv netaddr 192.168.3.2
>> bootp()192.168.3.1:bsd.rd
Setting $netaddr to 192.168.3.2 (from server )
Obtaining bsd.rd from server
5800832+476248 entry: 0xa800000020020000
ARCS64 Firmware Version 64.0
Found SGI-IP30, setting up.
Initial setup done, switching console.
Copyright (c) 1982, 1986, 1989, 1991, 1993
        The Regents of the University of California.  All rights reserved.
Copyright (c) 1995-2009 OpenBSD. All rights reserved.  http://www.OpenBSD.org

OpenBSD 4.5-current (OCTANE_RAMDISK) #1: Wed Apr 15 12:05:30 JST 2009
    root@puffy.s.axe-inc.co.jp:/home/asada/current/src/sys/arch/sgi/compile/OCTANE_RAMDISK
real mem = 536870912 (512MB)
rsvd mem = 1064960 (1MB)
avail mem = 502779904 (479MB)
mainbus0 at root
cpu0 at mainbus0: MIPS R12000 CPU rev 3.5 175 MHz with R10000 FPU rev 0.0
cpu0: cache L1-I 32KB D 32KB 2 way, L2 2048KB 2 way
clock0 at mainbus0: ticker on int5 using count register
xbow0 at mainbus0: XBow revision 5
xheart0 at xbow0 widget 8: Heart revision 6
onewire0 at xheart0
owserial0 at onewire0 family 0x0b sn 0000004d74fa
owserial0: "PM20400MHZ" serial 030-1476-001
"Odyssey" revision 2 at xbow0 widget 11 not configured
xbridge0 at xbow0 widget 15: Bridge revision 4
pci0 at xbridge0 bus 0
isp0 at pci0 dev 0 function 0 "QLogic ISP1020" rev 0x05: irq 0
isp0: invalid NVRAM header
scsibus0 at isp0: 16 targets, initiator 7
sd0 at scsibus0 targ 1 lun 0: <QUANTUM, ATLAS_V__9_SCA, 0238> SCSI3 0/direct fixed
sd0: 8682MB, 512 bytes/sec, 17781964 sec total
isp1 at pci0 dev 1 function 0 "QLogic ISP1020" rev 0x05: irq 1
isp1: invalid NVRAM header
scsibus1 at isp1: 16 targets, initiator 7
cd0 at scsibus1 targ 1 lun 0: <PLEXTOR, CD-ROM PX-12TS, 1.02> SCSI2 5/cdrom removable
ioc0 at pci0 dev 2 function 0 "SGI IOC3" rev 0x01: superio irq 4, ethernet irq 2
onewire1 at ioc0
owmac0 at onewire1 family 0x09 sn 000002d29696
owmac0: Ethernet Address 08:00:69:13:67:82
owserial1 at onewire1 family 0x0b sn 0000004d4ee4
owserial1: "FP1" serial 030-0891-003
owserial2 at onewire1 family 0x0b sn 0000004e12fb
owserial2: "PWR.SPPLY.ER" serial 060-0035-002

Trap cause = 7 Frame 0x9800000020009788
Trap PC 0xa800000020133ab4 RA 0xa800000020031ad4 fault 0xffffffffc012c9f8
0xa800000020133ab4 ra 0xa800000020031ad4 sp 0x98000000200098e0 (0xffffffffc015d800,0x900000f040500002,0x2,0x0)
0xa800000020031ad4 ra 0x0 sp 0x98000000200098e0
User-level: pid 0
stopped on non ddb fault
Stopped at      0xa800000020133ab4:     lbu     v0,0(a1)
0xa800000020133a68 (ffffffffc015d800,900000f040500002,2,0) sp 98000000200098e0 r
a a800000020031ad4, sz 0
0xa800000020031a70 (ffffffffc015d800,900000f040500002,2,0) sp 98000000200098e0 r
a 0, sz 0
User-level: pid 0
ddb>